THE VALUE OF HAVING A PLUMBER PUT IN YOUR DISHWASHER

The Value of Having a Plumber Put in Your Dishwasher

The Value of Having a Plumber Put in Your Dishwasher

Blog Article

Get Estimate
Most Common Dishwasher Installation
From transporting a dish washer into your home to affixing the water links, installing a dishwashing machine can take up to 5 hrs. A plumber will certainly have the right devices on hand and can install your new dish washer in under 2 hours.

A Plumber Can Examine the Supply Lines


A supply line, especially a dishwashing machine port, attaches the dishwashing machine to a water resource. A plumber can make certain that the line is compatible with both your dishwashing machine and also water resource if you buy a new supply line. An expert plumber can examine it to make certain that it's in good problem as well as does not have any type of leaks if you make a decision to use an existing supply line.

An Improper Setup Can Invalidate the Dish washer's Warranty


Prior to setting up a dishwashing machine on your own, you need to check out the warranty meticulously. Unless you are useful as well as have experience setting up dishwashers, you must work with a plumber so you don't risk your warranty.

Setting Up a Dishwasher Needs a Selection of Equipments


You might need to make a trip to Lowe's or Residence Depot if you do not have a selection of tools on hand. To mount a dishwashing machine, you require the complying with tools: pliers, a flexible wrench, a set of screwdrivers, a tube cutter, and also opening saws. You will certainly also need cleansing products such as a shallow container as well as sponge. If you do not have any of these items, the cost to purchase them can accumulate quickly.

Not Mounting Your Dish Washer Correctly Can Result In a Hill of Problems


Not only can mounting a dishwashing machine properly nullify your warranty, yet it can additionally create a mess. If you do not mount the supply line appropriately, you might deal with leaks-- or also worse, a flooding. You could additionally experience a "water hammer"-- when the water runs also promptly through your pipes as well as creates loud shaking sounds. Finally, if you inaccurately mount your dishwasher to the garbage disposal, you may notice pungent smells or have deposit on your recipes.

A Plumber Can End Up the Task Affordably and Quickly


A plumber can mount your dishwashing machine in one to two hours. The average plumber won't bill more than a pair of hundred dollars to install your dishwasher.
From hauling a dishwasher right into your home to connecting the water connections, mounting a dishwashing machine can take up to 5 hours. To make your life simpler and to avoid mounting a dishwashing machine improperly, we advise employing a professional plumber. A plumber will have the right tools on hand as well as can install your brand-new dishwasher in under 2 hours. A supply line, especially a dishwashing machine connector, attaches the dishwasher to a water source. Unless you are useful and also have experience installing dish washers, you must hire a plumber so you do not risk your service warranty.

How To Install A Dishwasher


Installing A Dishwasher Yourself


Just like other home appliances, a dishwasher helps to make chores less time-consuming and free of hassle. Most modern kitchens have a dishwasher or a cabinet space for dishwasher installation built into them. An older kitchen with no dishwasher or cabinet space for one might require a little reconstruction to accommodate dishwasher installation.


Installing a dishwasher requires basic knowledge of plumbing and electrical wiring. This article contains the steps involved in dishwasher installation, dishwasher installation tips, things to consider when installing a dishwasher in a kitchen that previously had no dishwasher in it, and tips for maintaining a dishwasher.


Steps Involved In Dishwasher Installation


Step One: Gather the Necessary Supplies


Gather all the required items and keep them near the installation site for easy reach. The materials and tools you will require include the following:


  • A screwdriver

  • • A hose clamp

  • • Duct tape (optional)

  • • A brass fitting

  • • Teflon tape

  • • A pair of pliers

  • • An adjustable wrench

  • • A drill

  • • Braided steel water line

  • • A pair of rubber hand gloves (optional)

  • • Wire nuts

  • Step Two: Take Safety Measures


    First, turn off the power socket and unplug the power cord if it is a plug-in dishwasher. Then, proceed to turn off the circuit breaker. Next, turn off the hot water shut-off valve under the kitchen sink and run the tap to ensure the water supply is shut off. Protect your kitchen floor close to the installation area with an old rug or a piece of drop cloth.


    Step Three: Remove the Old Dishwasher


    This step only applies if your kitchen has an old dishwasher that you want to replace. Remove the cabinet door to gain complete access to the old dishwasher. Next, remove the cover of the access panel located at the bottom front side of the dishwasher. Locate the junction box inside the access panel.


    Now, unscrew the terminal screws holding the wires in place at the junction box. Then, remove and tuck the wires out of the way with duct tape. Locate the dishwasher water inlet tube, undo the brass fitting and disconnect the water supply pipe from it. Put the disconnected end of the water supply line pipe into a bucket or bowl to collect any water remaining in it.


    Reach down beneath the sink to undo the drain hose. Loosen, then clamp and disconnect the drain hose of the dishwasher from the tailpiece of the sink. Next, put the disconnected end of the drain hose into a bucket to collect the water and debris.


    With all the connections out of place, remove the screws holding the dishwasher in place with a screwdriver, gently pull the dishwasher out from the cabinet and set it aside. You can use a piece of cloth or towel to clean up the mess made or any water spillage on the floor. Also, clean the cabinet where the old dishwasher was before installing a new one.


    Skip this step if you are having a dishwasher installed for the first time in your kitchen.


    Step Four: Install the New Dishwasher


    Connect the Water Supply


    Wrap Teflon tape on the tip of the water inlet pipe located at the bottom of the dishwasher. Screw on the 90 degrees brass fitting to the taped inlet pipe and tighten it with an adjustable wrench. Most dishwasher units do not include a brass fitting, but they are available at hardware stores.


    Once you have the fitting, connect the new water supply line to the elbow of the brass fitting. Pass the other end of the waterline through one of the cabinet holes and place it on the floor beneath the kitchen sink.


    Attach the Drain Line


    Locate the dishwasher drain standout pipe, connect the drain line to the dishwasher, and secure the connection with a hose clamp. Pass the other end of the drain line through the cabinet hole and place it towards the sink drain tailpiece


    Slide the Dishwasher into Place


    Attach the adjustable legs to the front of the dishwasher. Carefully slide the dishwasher under the countertop into the cabinet. Stop halfway and ensure everything is in a good position before sliding it in completely. Finish hooking up the water line by connecting the other end to the dual shut-off valve located under the kitchen sink.


    Proceed to connect the drain hose through an air gap to your garbage disposer, if you have any, or to the drain tailpiece of your sink. If you do not have an air gap, make a high loop with the drain hose before connecting it to the garbage disposal or the sink drain tailpiece.

    https://www.movementplumbing.com/blog/how-to-install-a-dishwasher


    Dishwasher Installation
    Call Today

    Report this page